How to Root Red Mulberry (Morus Rubra) Tree Cuttings

Summertime is such a fun time for kids when school is finally out. They often have time to think for themselves and be outside exploring this big grand world even if it is from within the scope of their own backyards or maybe a park close by. Half of the United States, from the Mississippi eastward is home to a wonderful fruit tree that almost always grows wild without any care from humans and produces bucket loads of fruit free for children. The red mulberry is the tree I remember finding early in the summer before the blackberries were ripe. They are so much easier to pick as the tree has no thorns. 

Now, I am happy to have a few mulberry trees on my property even if it's only to harvest a few handfuls to eat fresh after I get my mail on summer days. The fruit is soft and sweet and the seeds are barely perceptible when I eat them. I was pleased to find out that this tree will also root from cuttings while it is actively growing, unlike most fruit trees that root from dormant cuttings.

So, how to get these red mulberry tree cuttings to root? There are just a few steps that you can follow and within a few years, you can harvest your own mulberries!

1) Obtain fresh cuttings, preferably with a top leaf. You want to make sure that they cutting is still moist inside so that water can flow from the potting soil into the cutting. If you received them via mail, recut the bottom cut so that you are working with a fresh surface. Immediately place the cutting in water.

2) Prepare a pot by filling it with a well moistened mixture of half coconut coir and vermiculite. (You can also use perlite). Poke a hold in it the same diameter of the cutting about 4 inches deep

3) Dip the freshly cut end of the red mulberry cutting into a rooting hormone preparation

4) Carefully place the cutting into the prepared hole, sinking it down until there is only one node above the soil line

5) Press the soil firmly around the cutting, using your fingers.

6) Water the cutting with room temperature water - preferably non-chlorinated

7) Cover the cutting with a clear cup or bag to keep humidity levels high. 

8) Place the cutting some place warm and with indirect light for four to six weeks or until rooted.

9) Check the cutting every few days by lifting the cover and allowing fresh air in. Make sure the soil stays damp but not wet. 

10) Plant the rooted cutting into a new pot filled with good garden soil. Place outside in a sunny spot and make sure to keep soil damp. In the fall, you can plant your new tiny mulberry tree in permanent location where it will get plenty of sunshine, preferably near other trees but still have room to grow.

That's it. Pretty simple. Although I will say that sometimes the mulberry cuttings can be resistant to rooting. Don't expect more than 50 percent to succeed, unless you have a special touch!

You can check out my Etsy page, Wildflower Run to see if I have any mulberry cuttings in stock.

Full grown mulberry tree

How to Root Hops from Stem Cuttings

Photo by Michael Styne

A few years back, I was gifted some Humulus Lupulus 'Cascade' hop rhizomes to plant in an empty space in my yard for use in future beer brewing. 

We tended them so carefully and marked their spot in our yard so as not to mow over  any newly sprouting hop tendrils and then watched with excitement as they appeared, and grew, and grew some more until we had more growth than we ever expected. 

Hops grow fast and even are even considered invasive by some gardeners but it is not listed on the USDA Invasive Species List. (https://www.invasiveplantatlas.org/subject.html?sub=12189) They are a perennial bine that grows easily from 10 to 20 feet high in full sun with plenty of water and in good soil. Yes, a reliable means of asexual propagation is by splitting off some of the rhizomes that grow outward from the central root mass, but there is another way...

Did you know you don't have to do any digging? You can root cuttings from actively growing hops. 

Hops

My procedure is pretty simple.

1.  I remove a section of the bine, usually when I am pruning the plant in the spring and early summer. 
2. Trim the section into smaller 6-8 inch pieces that each have three to four growing nodes. 
3. Trim extra leaves, leaving one leaf at the top to photosynthesize carbohydrates for the cutting.
4. Place the cutting into a prepared rooting mix of dampened coco coir and vermiculite mix so that the top growth node is sitting on the top of the mixture.
5. Keep the cutting moist but not wet  and in a shady but warm spot for the next two weeks or so or until you notice the new roots.
6. Transfer the cutting to a plant pot filled with regular potting soil  and keep moist until you are ready to plant it outside in a permanent location.

Freshly sprouted hop plant

Note: These plants are so easy to root that I have just stuck my pruned cuttings into a bucket of water and forgotten about them for a couple of weeks only to find they had rooted themselves, so don't be too intimidated by the details.

If you would like a more in depth article on this process, you can click here. 

I hope you give rooting a hop vine a try, as I think you will be happily rewarded for your efforts.

Just make sure you are not propagating a patented vine. You can just insert the variety of the hop name on the Google Patent Search page and find out quickly whether you can proceed legally.

Sometimes in the early spring, I sell Cascade Hop cuttings on my Etsy page, Wildflower Run.